Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Here below you can find some high-quality data in relation to A Step-by-Step Guide to Installing a Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a tub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a new one is also a reasonably challenging project. If the old bathtub is conveniently available, the task can relocate speedily; if you need to open up a wall surface to remove the old bathtub as well as place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will need an assistant to leave the old tub as well as set in the brand-new one. Make sure you have certified yourself for the work and are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed task, it is much better to take into consideration employing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly aid you set up a new tub in your bathroom if you have already gotten a new tub and also don't need to transform the arrangement of your previous water system pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic because of the restricted gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making certain that the washers are in location between the faucet and also the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be connected to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub until the level checks out degree.
To set up taps, fit all-time low of the outermost flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the supply of water as well as examine all joints and new pipework for leaks and tighten them if required. Load the bath tub and likewise check the overflow outlet and the normal outlet for leaks.
Finally, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub ought to wait until the bathtub has actually been made use of at the very least once as this will resolve it right into its final position.
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with moisture and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealant can crack relatively early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that write-up about Installing A Bathtub from a friend on a different web address. Enjoyed our write up? Please share it. Help other people locate it. Many thanks for your time spent reading it.
Pro assistance? Dial. Report this page